Caple C806C Especificações descarregar pdf (Página 10)

Digital Fiber Sensor FX-100 SERIES

132

FIBER

SENSORS

LASER

SENSORS

PHOTO-

ELECTRIC

SENSORS

MICRO

PHOTO-

ELECTRIC

SENSORS

AREA

SENSORS

SAFETY

COMPONENTS

PRESSURE

SENSORS

INDUCTIVE

PROXIMITY

SENSORS

PARTICULAR

USE

SENSORS

SENSOR

OPTIONS

WIRE-

SAVING

SYSTEMS

MEASURE-

MENT

SENSORS

STATIC

CONTROL

DEVICES

LASER

MARKERS

Selection

Guide

Fiber Sensor

Amplifiers

FX-300

FX-100

Fibers

FT / FD / FR

FX-410

FX-311

FX-11A

FX-301-F

Other

Products

FIBER

SENSORS

FX-100

Fiber Sensor

Ampliﬁ ers

SPECIFICATIONS

Notes: 1) Where measurement conditions have not been speciﬁ ed precisely, the conditions used were an ambient temperature of +23 °C +73.4 °F.

2) When using the interference prevention function, set the emission frequencies for the ampliﬁ ers to be covered by the interference prevention function to

different frequency values.

However, the interference prevention function does not operate at emission frequency 0 (factory default setting) for the FX-101(P)(-Z) / FX-101(P)-CC2.

3) The voltage withstandability and the insulation resistance values given in the above table are for the ampliﬁ er only.

4) Connector attached cable CN-14A-C2 is not attached to the models that have no “-CC2” at the end of the model Nos.

Make sure to use the optional connector attached cable CN-14A(-R)-C□ or the connector CN-14A, or a connector manufactured by J.S.T. Mfg., Ltd.

(contact: SPHD-001T-P0.5, housing: PAP-04V-S).

Model Nos. having the sufﬁ x “-Z” are M8 plug-in connector type. Make sure to use the optional M8 attached connector cable CN-24A-C□.

Type

Standard type Long sensing range type

Cable set Cable set

Model No.

NPN output FX-101(-Z) (Note 4) FX-101-CC2 FX-102(-Z) (Note 4) FX-102-CC2

Item PNP output FX-101P(-Z) (Note 4) FX-101P-CC2 FX-102P(-Z) (Note 4) FX-102P-CC2

Supply voltage 12 to 24 V DC ± 10 % Ripple P-P 10 % or less

Power consumption

Normal operation: 720 mW or less (Current consumption 30 mA or less at 24 V supply voltage)

ECO mode: 600 mW or less (Current consumption 25 mA or less at 24 V supply voltage)

Output

NPN open-collector transistor

• Maximum sink current: 100 mA

•

Applied voltage: 30 V DC or less (between output and 0 V)

• Residual voltage: 1.5 V or less (at 100 mA sink current)

PNP open-collector transistor

• Maximum source current: 100 mA

•

Applied voltage: 30 V DC or less (between output and +V)

•

Residual voltage: 1.5 V or less (at 100 mA source current)

Output operation Selectable either Light-ON or Dark-ON, at SET mode

Short-circuit protection Incorporated

External input

NPN non-contact input

• Signal condition

High: +8 V to +V DC or Open

Low: 0 to +2 V DC

(Source current 0.5 mA or less)

• Input impedance: 10 kΩ approx.

PNP non-contact input

• Signal condition

High: +4 V to +V DC

(Sink current 0.5 to 3 mA)

Low: 0 to +0.6 V DC or Open

• Input impedance: 10 kΩ approx.

Response time

Emission frequency 0: 250 μs or less (factory default setting)

Emission frequency 1: 450 μs or less

Emission frequency 2: 500 μs or less

Emission frequency 3: 600 μs or less

Emission frequency 1: 2.5 ms or less (factory default setting)

Emission frequency 2: 2.8 ms or less

Emission frequency 3: 3.2 ms or less

Emission frequency 4: 5.0 ms or less

Sensitivity setting 2-level teaching / Limit teaching / Full-auto teaching

Operation indicator Orange LED (lights up when the output is ON)

Digital display 4 digits (green) + 4 digits (red) LCD display

Fine sensitivity adjustment function

Incorporated

Timer function

ON-delay / OFF-delay timer, switchable either effective or ineffective

[Timer period: 1 ms, 5 ms, 10 ms, 20 ms, 40 ms, 50 ms, 100 ms, 500 ms, 1,000 ms]

Attenuation function

Incorporated

Switchable either effective or ineffective

Interference prevention

function

Incorporated

Emission frequency selection method (Note 2)

(Functions at emission frequency 1, 2 or 3)

Incorporated

Emission frequency selection method (Note 2)

(Functions at emission frequency 1, 2, 3 or 4)

Environmental resistance

Ambient temperature

–10 to +55 °C +14 to +131 °F (If 4 to 7 units are mounted close together: –10 to +50 °C +14 to +122 °F, if 8 to 16 units are mounted close together:

–10 to +45 °C

+14 to +113 °F) (No dew condensation or icing allowed), Storage: –20 to +70 °C –4 to +158 °F

Ambient humidity 35 to 85 % RH, Storage: 35 to 85 % RH

Ambient illuminance Incandescent light: 3,000 ℓx at the light-receiving face

Voltage withstandability 1,000 V AC for one min. between all supply terminals connected together and enclosure (Note 3)

Insulation resistance 20 MΩ, or more, with 250 V DC megger between all supply terminals connected together and enclosure (Note 3)

Vibration resistance 10 to 150 Hz frequency, 0.75 mm

0.030 in amplitude in X, Y and Z directions for two hours each

Shock resistance 98 m/s

acceleration (10 G approx.) in X, Y and Z directions for ﬁ ve times each

Emitting element (modulated) Red LED (Peak emission wavelength: 632 nm

0.025 mil)

Material Enclosure: Polycarbonate, Key switch: Polycarbonate, Fiber lock lever: PBT

Connecting method Connector (Note 4)

Cable length Total length up to 100 m

328.084 ft is possible with 0.3 mm

, or more, cable.

Weight

Net weight: 15 g approx.

Gross weight: 35 g approx.

Net weight: 15 g approx.

Gross weight: 75 g approx.

Net weight: 15 g approx.

Gross weight: 35 g approx.

Net weight: 15 g approx.

Gross weight: 75 g approx.

Accessory

–

CN-14A-C2

(Connector attached cable, 2 m 6.562 ft long): 1pc.

–

CN-14A-C2

(Connector attached cable, 2 m 6.562 ft long): 1pc.

Refer to p.101~ for ﬁ ber speciﬁ cations.

1 2 ... 5 6 7 8 9 10 11 12 13 14 15 16

FX-100 SERIES 1

Comentários a estes Manuais

Sem comentários

Caple C806C Especificações Página 10

Comentários a estes Manuais

Manuais e produtos relacionados com Fogões Caple C806C